자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Fixing a door hinge that is loose is a simple task for the majority of homeowners. If, however, the screw holes are stripped and aren't able to hold screws, you might have to put in dowels and wood glue before you can put back the hinge.

Before you do that though, brush away the surface corrosion. This will help the dowels stay in place and give them a solid base to rest on.

Removing the Hinges

Most hinges on doors are removable, which makes it easier to move the door from one side to another or take the entire door off of the frame, if needed. The removal of the hinges is easy for anyone with a bit of patience, though you do need to know how do it right.

If the hinges are painted you will need to remove the paint prior to trying to remove the pins. You could scratch your door if you do not remove the paint. To break the seal, place the hinges in a stainless steel dish and fill the pan with water until the hinges are completely submerged. Let the hinges sit in the pan for about 30 minutes. The heat from the water should soften the paint and make it easier to get rid of the pins.

After the pins have been loosened, remove the hinges and the frame from the door. It is possible to use a standard screwdriver, however you should use a magnetic screwdriver for this job. This type of screwdriver was created to grab screws made of metal and can make the work go much faster.

It is a good idea to spray lubricant on the hinges prior to attempting to remove them. A simple lubricant will allow you to speed up the process and remove the pins and screws more easily. This kind of lubricant can be found at most hardware stores and home improvement stores.

Keep in mind that the number of door hinges you will need will differ based on the kind of door and the configurations. Heavier doors and solid-core doors will require more hinges, while lighter-weight and hollow-core doors might require just two or three.

It is also essential to know the various types of hinges so you can decide which one will work best in your situation. Exterior hinges are designed to support the weight of a door, but interior hinges must be able to handle heavier loads.

Reattaching the Hinges

Sometimes, the hinges on doors get looser and eventually begin to hang crookedly or sag. It can be a big problem, but the fix is usually quite simple. In most cases it's a simple tightening of the screw will resolve the issue. However, if the screw holes are stripped out, this can be more difficult. However, there is a trick to get the holes back in place using a wooden dowel.

Begin by drilling the old hole using a drill bit close to the new screw size (normally 3/8"). Then, you can use wood glue and a dowel made of wood to fill in the hole. The dowel should be cut to a length exactly the same as the screw to ensure a snug fit. Then, you can reinstall the screw and tighten it until the desired level of tightness. If the door continues to have a tendency to bind the door, then add a second dowel to the gap and repeat the process. Close the door slowly after each adjustment to make sure that the perimeter clearances are in order.

You could also use a wood plug in place of the dowel. It works just as well but might take a little longer to install. Simply whittle a piece of wood that is the appropriate size for a comfortable fit, then press it into the hole. If you don't own a woodworking instrument or toothpicks, you can make use of toothpicks or wooden matchsticks.

Once you have reinstalled the new screw and countersink the screw, you can use a countersink tool to make the hole for the head of the screw smaller, so that it doesn't touch the edge of the door when it's opened and closed. This will make it much easier to tighten the screws when reinstalling hinges.

After you have reinstalled the hinge, make sure to lubricate it with a dry lubricant to help keep it from getting stuck in the future. You can use products like PB Blaster and Liquid Wrench. Apply a thin layer and allow it to soak into the hinge barrel for about 15 minutes.

Refinishing the Hinges

If you're not sure if you're ready to replace the hinges on your door, you can make a few repairs. Make sure the screws that attach the hinge plate in place to the door frame and the frame are tight. If they're loose, tighten them with an electric drill or screwdriver. Be careful not too tighten the screws, as this can create gaps at the trim joints or worse, strip the threads.

If the problem is that the hinge plates are breaking away from the jamb and door, you can reattach them by gluing wood glue to the back of the plates, and then inserting wooden dowels or toothpicks into the holes. The toothpicks or dowels will give a solid foundation for the screws and help prevent the plates from shifting when you drive them into position. Allow the glue to dry before attaching the hinge.

The screws could also be stripped or missing. You can fix this problem by replacing the screws with longer ones. Use a drill that is exactly the same size as the screw hole to avoid drilling into the jamb or hinge.

Close the door after you have reattached your hinge and check the gap between the frame and the door. The gap should be the thickness of a penny all around or less if an older door was hung incorrectly. If the hinges were set up properly, this shouldn't be an issue.

If you find that the hinges are loose, you can try adding an extra thicker shim between the hinge plate and the mounting surface to add a little extra space. You could also try taking the hinge pin from the problematic hinge and pounding it down with a hammer in order to make it tighter or use a new hinge pin altogether. You can also lubricate your repair window hinges with mineral oil or jojoba to reduce friction and help keep them in their place. Lubricating your hinges frequently will help keep them from becoming stiff and squeaky and can also prolong their life.

Cleaning the Hinges

The friction caused by the constant movement of a hinge attracts dust particles. These particles can become stuck and accumulate in the moving parts of door hinges if they're not regularly cleaned and lubricated. In the end the hinge can become stiff and creaky and its appearance may deteriorate rapidly. Regular cleaning, lubrication, and inspections will maintain the quality and function of upvc window hinges on a door.

Check the hinges for the accumulation of rust. If the rust has become so severe that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace the hinges. If you are able to save the hinges, remove any loose rust using steel wool and wire brush. Apply a commercial rust removal solution or a homemade solution such as lemon juice to the hinge. Let the rust-removing solution be on the hinges for a few minutes to penetrate and dissolve the remaining rust.

Retightening screws can help restore hinge function If you don't wish to spend money or time to replace window hinges uk hinges (click4r.com) hinges. If you've sanded the screw holes however, it might be necessary to attach an wooden dowel or shim to the hinge. Dowels made of wood are square pieces of wood in the form of rods which are available in varying lengths and diameters. They can be purchased online, at woodworking supply shops and at home improvement stores.

A shim could also be made from metal or plastic, depending on the type of hinge you've got. To make a dowel, you need to cut a dowel from wood to the desired length. Then, dip a dowel into carpenter's adhesive and place it in the hole. The glue will hold the dowel securely in the position.

Before cleaning the hinges put down a paper cloth or towel to protect your flooring from spills. After the area has been secured and dry, clean the hinges with a soft sponge or cloth that has been soaked in mild cleaner or vinegar to eliminate the build-up of dirt, grime and tarnish. You can make use of a small or toothbrush brush to reach hard-to-reach spots in crevices or tight areas.